| View previous topic :: View next topic |
| Author |
Message |
gotmullet?
Member White Shrimper Boot Club
Joined: 26 Nov 2009
Posts: 912
Location: Corpus
|
 Posted: Sat Nov 02, 2013 12:49 am Post subject: Outboard Motor Parts Question |
 |
|
My boat motor drive shaft snapped in half and I'm having a hard time finding a replacement.
I tried all the Johnson Dealers, ebay, salvage yards on the internet and no luck.
It seems the part I am looking for is obsolete anywhere I look.
Engine model # J8RESR
Part # 033254
25 1/2" drive shaft.
Anyone on here have any recommendations?
Thanks in advance...
_________________
"Do not call my Jeep a Car ever again " |
|
| Back to top |
|
 |
joejoe7716
Horse Mullet
Joined: 04 Aug 2012
Posts: 195
Location: South Texas
|
| Posted: Sat Nov 02, 2013 6:40 am Post subject: Re: Outboard Motor Parts Question |
|
|
| gotmullet? wrote: | My boat motor drive shaft snapped in half and I'm having a hard time finding a replacement.
I tried all the Johnson Dealers, ebay, salvage yards on the internet and no luck.
It seems the part I am looking for is obsolete anywhere I look.
Engine model # J8RESR
Part # 033254
25 1/2" drive shaft.
Anyone on here have any recommendations?
Thanks in advance... |
www.vikingmarine.com
His name is Ron out of Florida....
His service isn't all that great but has a warehouse full of outboard parts. |
|
| Back to top |
|
|
speckled.trout
Full Grown Flour Bluffian
Joined: 30 Aug 2012
Posts: 1190
|
| Posted: Sat Nov 02, 2013 8:17 am Post subject: |
|
|
Shouldn't that P/N be 0334254? Typo?
Anyway, that part is no longer made in either a Johnson part or a Evinrude
part, which both motors use the same shaft. Going to be a really tuff one
most people just have a machine shop make the shaft for them.
If you have the old one it can be used as the pattern.
Cost may be more than you want to spend.
ST |
|
| Back to top |
|
|
gotmullet?
Member White Shrimper Boot Club
Joined: 26 Nov 2009
Posts: 912
Location: Corpus
|
| Posted: Sat Nov 02, 2013 9:14 am Post subject: |
|
|
| speckled.trout wrote: | Shouldn't that P/N be 0334254? Typo?
Anyway, that part is no longer made in either a Johnson part or a Evinrude
part, which both motors use the same shaft. Going to be a really tuff one
most people just have a machine shop make the shaft for them.
If you have the old one it can be used as the pattern.
Cost may be more than you want to spend.
ST |
Yes that was a typo.
0334254 is the part I'm looking for.
I will consider anything at this point to get me back in the water.
_________________
"Do not call my Jeep a Car ever again " |
|
| Back to top |
|
|
richard moreland
Finger Mullet
Joined: 25 Aug 2008
Posts: 19
|
| Posted: Sat Nov 02, 2013 10:23 am Post subject: |
|
|
Year and HP  |
|
| Back to top |
|
|
JayM5209
Finger Mullet
Joined: 30 Jul 2011
Posts: 23
Location: Fond du Lac, WI
|
| Posted: Sat Nov 02, 2013 10:36 am Post subject: |
|
|
| These guys may be able to help - Twin Cities Outboard at http://www.twincityoutboard.com/. Worth a call or email inquiry. |
|
| Back to top |
|
|
gotmullet?
Member White Shrimper Boot Club
Joined: 26 Nov 2009
Posts: 912
Location: Corpus
|
| Posted: Sat Nov 02, 2013 11:47 pm Post subject: |
|
|
| richard moreland wrote: | | Year and HP |
1990
8hp
_________________
"Do not call my Jeep a Car ever again " |
|
| Back to top |
|
|
ironmanstan
Exalted Ruler of Flour Bluff
Joined: 04 Oct 2006
Posts: 12256
|
| Posted: Sun Nov 03, 2013 12:57 pm Post subject: |
|
|
| gotmullet? wrote: | | richard moreland wrote: | | Year and HP |
1990
8hp |
I wonder what the Rockwell hardness is on that shaft? Did it twist or just snap. Is the break clean or rough. What made it break? It's just an 8hp. If it was mine and I could see the break I might would attempt a 100% welded repair. I wonder what type of metal/alloy it's made from? You know like 1080, 4130, 4140,? Just IMS thinking.........nowadays the gears make more clanking noise when they turn. 
_________________
I LIKE MINE FRIED. |
|
| Back to top |
|
|
speckled.trout
Full Grown Flour Bluffian
Joined: 30 Aug 2012
Posts: 1190
|
| Posted: Sun Nov 03, 2013 2:16 pm Post subject: |
|
|
Hey IMS the material is 17-4 stainless, Rockwell C35
tensile 160K / yield 145K
ST |
|
| Back to top |
|
|
ironmanstan
Exalted Ruler of Flour Bluff
Joined: 04 Oct 2006
Posts: 12256
|
| Posted: Sun Nov 03, 2013 3:53 pm Post subject: |
|
|
| speckled.trout wrote: | Hey IMS the material is 17-4 stainless, Rockwell C35
tensile 160K / yield 145K
ST |
Nice I heat treat 17-4ph almost on a daily basis. 1900 degs for 20 -30 minutes and for this hardness a 1025 deg temper for 4 hours...known as h1025. I could only find that they are a stainless .....good research job Mike.
_________________
I LIKE MINE FRIED. |
|
| Back to top |
|
|
speckled.trout
Full Grown Flour Bluffian
Joined: 30 Aug 2012
Posts: 1190
|
| Posted: Sun Nov 03, 2013 4:15 pm Post subject: |
|
|
can sub.... Monel 500 (K-monel)
ST |
|
| Back to top |
|
|
speckled.trout
Full Grown Flour Bluffian
Joined: 30 Aug 2012
Posts: 1190
|
| Posted: Sun Nov 03, 2013 5:48 pm Post subject: |
|
|
hey gotmullet? if you decide to have the part made let me know I'll see if I can find some round bar for you, will need to know diameter.
ST |
|
| Back to top |
|
|
gotmullet?
Member White Shrimper Boot Club
Joined: 26 Nov 2009
Posts: 912
Location: Corpus
|
| Posted: Mon Nov 04, 2013 3:07 am Post subject: |
|
|
| speckled.trout wrote: | hey gotmullet? if you decide to have the part made let me know I'll see if I can find some round bar for you, will need to know diameter.
ST |
Good Deal...
I took it to a machine shop and should know more by Monday.
If they are unable to fix it I'll post pics of the area of the shaft that snapped.
_________________
"Do not call my Jeep a Car ever again "
Last edited by gotmullet? on Mon Nov 04, 2013 8:25 am; edited 1 time in total |
|
| Back to top |
|
|
gotmullet?
Member White Shrimper Boot Club
Joined: 26 Nov 2009
Posts: 912
Location: Corpus
|
| Posted: Mon Nov 04, 2013 3:12 am Post subject: |
|
|
There is a fine smooth indention on the shaft and the "break" is the the right hand side of it.
The second pic are the ends of the drive shaft.
[/img]
_________________
"Do not call my Jeep a Car ever again " |
|
| Back to top |
|
|
beachbandit
Finger Mullet
Joined: 06 Aug 2012
Posts: 47
Location: SO.TX
|
| Posted: Mon Nov 04, 2013 3:16 pm Post subject: |
|
|
there is a place in salina ks. that would have that part..ill try to find the name this guy has everything
_________________
fish big..
Beachbandit |
|
| Back to top |
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
